Axiohm A794-D100 Manual de instrucciones Pagina 32
- Pagina / 147
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
A794 Owner’s Guide Chapter 4: Print Specifications
December 1999 27
Paper Specifications
The printer requires qualified thermal paper with the following dimensions:
Width Diameter Length
80 mm ± .2 mm (3.15 in. ± .02 in.) 90 mm max. (3.54 in.) 322 ft. nominal.
82.5 mm ± .2 mm (3.25 in. ± .02 in.) 90 mm max. (3.54 in.) 322 ft. nominal.
The paper must not be attached at the core. Use paper with a colored stripe at the end
to indicate that the paper is running low.
The above figures are based on a core diameter of 22 ± .5 mm (.87 in.) outside,
11.5 ± .5 mm (.45 in.) inside.
Print Zones
Print Zones for 80 mm Paper
Specifications of print zone for 80 mm paper:
♦
576 dots (addressable) @ 8 dots/mm, centered on 80 mm
♦
Standard Mode: minimum margins: 2.5 mm (.098 inches)
♦
Top margin to manual tearoff: 17.8 mm (0.70 inches)
♦
Top margin to knife cut: 19.0 mm (0.75 inches)
Cut Edge
44 Standard Columns = 71.5 mm (2.815 in.)
56 Compressed Columns = 70 mm (2.756 in.)
Cut Edge
Paper Width = 80 mm (3.15 in.)
Top Margin, 17.8 mm (.70 in.) Minimum
Printable Zone, 576 Dots = 72 mm (2.835 in.)
Nominal Margins, 4 mm (0.157 in.)
- Owner's Guide 1
- Legal Notices 2
- December 1999ii 3
- Contents 4
- Chapter 1: About the Printer 6
- Description of Printer 7
- Models Available 8
- Features 9
- Chapter 2: Using the Printer 10
- Unpack the Printer 11
- Choose a Location 13
- Connect the Cables 14
- Cash Drawer Cables 15
- Power Supply Cable 15
- Printer Controls 16
- Loading Receipt Paper 18
- Configuring the Printer 21
- December 1999 17 22
- Troubleshooting the Printer 23
- Printing Problems 24
- Printer Does Not Function 24
- December 199920 25
- Ordering Thermal Paper 26
- Ordering Cash Drawers 28
- Ordering Communication Cables 29
- Wall-Mount Kit 29
- Characters 31
- Paper Specifications 32
- Print Zones 32
- Print Zones for 82.5 mm Paper 34
- Character Sets 37
- Code Page 850 38
- Code Page 852 39
- Code Page 858 40
- Code Page 860 41
- Code Page 863 42
- Code Page 865 43
- Code Page 866 44
- Code Page 1252 45
- Communication Overview 47
- RS-232C Interface 48
- XON/XOFF Protocol 49
- DTR/DSR Protocol 50
- Power Connector 51
- Cash Drawer Connector 51
- RS-232C Settings 52
- Parallel Interface 53
- Command Conventions 55
- List of Commands and Location 56
- By Function 60
- Print Characteristic Commands 61
- Graphics Commands 62
- Barcode Commands 63
- Comparisons 65
- Command Descriptions 66
- Perform Partial Knife Cut 67
- Generate Tone 67
- Initialize Printer 68
- Bit Sensor 0 1 70
- Sensor Status 70
- Select Cut Mode and Cut Paper 71
- Print Test Form 72
- Print and Feed One Line 73
- Activate Carriage Return 73
- Print Lines 73
- Dot Rows 74
- Extra Dot Rows 74
- Set Line Spacing to 1/6 Inch 75
- Set Line Spacing 75
- Print and Feed Paper 76
- Print and Feed 76
- Horizontal Tab 77
- Set Column 77
- Set Horizontal Tab Positions 79
- Set Relative Print Position 80
- Select Justification 81
- Set Left Margin 82
- Set Printing Area Width 83
- Select Double-Wide Characters 84
- Select Single-Wide Characters 84
- Select Pitch (Column Width) 85
- Select Print Mode 87
- Cancel User-Defined Character 90
- Select or Cancel Italic Print 92
- Select Character Size 93
- Character Width Selection 94
- Hex Decimal Width 94
- Character Height Selection 94
- Hex Decimal Height 94
- Summary of Rotated Printing 96
- Download BMP Logo 98
- Select Bit Image Mode 99
- December 1999 95 100
- Related Information 100
- Select the Current Logo 103
- Define Downloaded Bit Image 104
- Print Downloaded Bit Image 105
- Status Commands 106
- Value of 107
- Function Description 107
- Bit 0 Bit 1 107
- Status Byte 108
- (RS-232) 108
- Type ID ( 109
- ASCII Hex Dec 110
- Real Time Commands 115
- Auto Status Back 122
- Bar Code Commands 126
- Print Bar Code 127
- Select Bar Code Width 128
- Page Mode Commands 129
- Print Data in Page Mode 130
- Select Page Mode 130
- Select Standard Mode 131
- (x0, y0) 132
- (x0 + dx, y0 + dy) 132
- Print Area 132
- Macro Commands 135
- Execute Macro 136
- User Data Storage Commands 137
- Erase User Flash Sector 139
- Flash Download Commands 140
- Get Firmware CRC 141
- Return Microprocessor CRC 142
- Return Main Program Flash CRC 142
- Erase Selected Flash Sector 142
- Reset Firmware 143
- A794 Owner’s Guide Index 144
- December 1999 139 144
- Index A794 Owner’s Guide 145
- December 1999140 145
- December 1999 141 146
- © 1999 AXIOHM 147
- Printed in U.S.A 147
Relacionado con productos y manuales para Impresión y escaneo Axiohm A794-D100
Impresión y escaneo Axiohm 7156 Especificaciones
(190 paginas)
(190 paginas)
Impresión y escaneo Axiohm 7193 Especificaciones
(85 paginas)
(85 paginas)
Impresión y escaneo Axiohm A758 Guia de preparacion
(19 paginas)
(19 paginas)
Impresión y escaneo Axiohm A795 Guía de usuario
(128 paginas)
(128 paginas)
Impresión y escaneo Axiohm A758 Manual de instrucciones
(217 paginas)
(217 paginas)
Impresión y escaneo Axiohm 7156 Especificaciones
(36 paginas)
(36 paginas)
Impresión y escaneo Axiohm Astrium Especificaciones
(14 paginas)
(14 paginas)
Impresión y escaneo Axiohm 7193 Especificaciones
(84 paginas)
(84 paginas)
Impresión y escaneo Axiohm A630 Manual de usuario
(63 paginas)
(63 paginas)
Impresión y escaneo Axiohm 7193 Especificaciones
(104 paginas)
(104 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.220 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales