Axiohm APOS PRINTER SERIES Manual de usuario Pagina 112
- Pagina / 138
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APOS Premium Printer Series User Manual Page 111 /136 Reference: FDE 3107312 Issue A
S
ELECT FLASH MEMORY SECTOR TO DOWNLOAD
Selects the flash sector (nn) for which the next download operation applies.
The values of the possible sector are restricted, depending upon the flash part type.
The printer transmits an ACK if the sector number is acceptable or an NAK if the sector number is not
acceptable. Sector numbers start at 0
ASCII
GS STX nn
Hexadecimal 1D 02 nn
Decimal
29 2 nn
Value and Range of n 0-15 = 1M bytes Flash
Exceptions : Available only in download mode.
G
ET FLASH FIRMWARE CRC STATUS
Causes the printer to calculate the CRC for the Flash firmware code space and transmits the result.
This is performed normally after downloading completely a new firmware to verify that the downloaded
firmware is valid
The printer transmits ACK if the calculated CRC is correct; NAK if the CRC is incorrect
ASCII
GS ACK
Hexadecimal 1D 06
Decimal
29 6
R
ETURN BOOT SECTOR CRC
Returns the CRC calculated over the boot sector code space.
ASCII
GS BEL
Hexadecimal 1D 07
Decimal
29 7
Formulas
ACK <low byte> <high byte>
- APOS PREMIUM PRINTER SERIES 1
- USER MANUAL 1
- EVOLUTIONS 2
- CONTENTS 3
- 1 GENERAL DESCRIPTION 6
- 2 SPECIFICATIONS 7
- 2.4 Operational performance 9
- 2.5 Characters 10
- 2.5.3 Print zone 11
- 10 x 24 Font 12
- 13 x 24 Font 12
- 2.5.7 Character sets 14
- 3 WARRANTY 24
- 4 YOUR PRINTER 25
- 4.1.5 Cutter 26
- 4.1.6 Connectors 26
- 4.1.7 Cable traps 26
- 4.1.8 Mounting holes 26
- 4.1.9 Sensors 26
- 4.3 Loading paper 27
- 4.4 Light indicator 27
- 4.5 Connectors & cables 27
- 4.5.1 Power connector 28
- CONNECTOR VIEW PINOUT 29
- 4.6.1 RS232 30
- 4.6.2 USB PARAMETERS 31
- 4.7 Self test description 32
- 4.8 Configuration menu 34
- 5 LIST OF CONTROL CODES 36
- 6 COMMAND DESCRIPTION 40
- 6.2 Reset commands 41
- 6.3 Paper Cut commands 42
- ELECT CUT MODE AND CUT PAPER 43
- 6.4 Sensor commands 44
- EED N DOT ROWS 46
- DD N EXTRA DOT ROWS 46
- ET LINE SPACING 48
- RINT AND FEED PAPER 48
- RINT AND FEED N LINES 49
- ORIZONTAL TAB 50
- ET HORIZONTAL TAB POSITIONS 51
- ET RELATIVE PRINT POSITION 52
- ELECT JUSTIFICATION 53
- ET LEFT MARGIN 53
- Left margin→ 53
- Printing area width→ 53
- ET PRINTING AREA WIDTH 54
- 6.7 Printer configuration 55
- ELECT PRINT MODE 56
- ELECT DOUBLE-WIDE CHARACTERS 57
- ELECT SINGLE-WIDE CHARACTERS 57
- ELECT OR CANCEL ITALIC PRINT 59
- ELECT CHARACTER SIZE 61
- UMMARY OF ROTATED PRINTING 63
- 6.9 Font commands 64
- ANCEL USER-DEFINED CHARACTER 67
- ELECT CHARACTER SET 67
- ELECT CHARACTER CODE TABLE 68
- 6.10 Graphics Commands 70
- ELECT BIT IMAGE MODE 71
- 6.11 Logo commands 74
- EFINE DOWNLOADED BIT IMAGE 75
- OWNLOAD BMP LOGO 76
- RINT DOWNLOADED BIT IMAGE 76
- ETURN LOGO CHECKSUM 77
- RANSMIT CASH DRAWER STATUS 78
- RANSMIT PAPER SENSOR STATUS 79
- UFFERED STATUS TRANSMISSION 79
- RANSMIT PRINTER ID 82
- RANSMIT STATUS 89
- ETURN SRAM SIZE 90
- ETURN CPU FREQUENCY 90
- END PRINTER SOFTWARE VERSION 91
- 6.13 Real Time Commands 92
- EAL TIME RECOVERY FROM FAULT 93
- EAL TIME STATUS TRANSMISSION 95
- 6.14 Bar Code Commands 98
- RINT BAR CODE 99
- ELECT BAR CODE WIDTH 100
- 6.15 Page Mode Commands 101
- RINT DATA IN PAGE MODE 102
- ELECT PAGE MODE 102
- ELECT STANDARD MODE 103
- ET PRINT AREA IN PAGE MODE 105
- 6.16 Macro Commands 108
- ENERATE SOLENOID PULSE 109
- WITCH TO FLASH DOWNLOAD MODE 111
- ETURN FLASH MEMORY SIZE 111
- ET FLASH FIRMWARE CRC STATUS 112
- ETURN BOOT SECTOR CRC 112
- ETURN MAIN PROGRAM FLASH CRC 113
- RASE SELECTED FLASH SECTOR 113
- 6.19 Boot Download 115
- User Flash Memory Commands 116
- User Data Storage Commands 118
- Peripheral control commands 118
- ROCESS TICKET COUNTER 119
- EQUEST TICKET COUNTER 119
- ET CUT TAG 120
- EQUEST CUT TAG 120
- 6.24 Easy Font Support 121
- OWNLOAD SINGLE BYTE FONT 122
- OWNLOAD DOUBLE BYTE FONT 123
- ELETE FONTS 125
- HECK EASYFONT COMPATIBILITY 125
- 6.25 Configuration commands 126
- ET PRINT DENSITY 127
- ET PREHEATING OPTION 127
- ET KNIFE OPTION 128
- ET PARTIAL CUT DISTANCE 128
- ET QUEUE TICKET MODE 129
- ET DEFAULT FONT 129
- Description: 130
- ET DIAGNOSTICS MODE 131
- ET DEFAULT CODE PAGE 132
- EEPROM 133
- 7 TROUBLESHOOTING 134
- 7.2.3 Printing Problems 135
- 8 CLEANING YOUR PRINTER 136
- 9 SPARES 137
Relacionado con productos y manuales para Impresión y escaneo Axiohm APOS PRINTER SERIES
Impresión y escaneo Axiohm Astrium Especificaciones
(14 paginas)
(14 paginas)
Impresión y escaneo Axiohm 7193 Especificaciones
(84 paginas)
(84 paginas)
Impresión y escaneo Axiohm A630 Manual de usuario
(63 paginas)
(63 paginas)
Impresión y escaneo Axiohm 7193 Especificaciones
(104 paginas)
(104 paginas)
Impresión y escaneo Axiohm A630 Manual de usuario
(27 paginas)
(27 paginas)
Impresión y escaneo Axiohm 7156 Especificaciones
(314 paginas)
(314 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales